RV Bathtub Replacement in 13 Fast, Easy Steps

RV bathtubs are nice to have, but when it comes time to take on the task of a replacing a tub you can either pay a professional or do the job yourself. This RV bathtub replacement isn’t too difficult if you know what to expect. Ready to give it a try? Here’s what you need to know.

<a href=RV bathtub replacement" />Replacing your RV bath tub is easier than you think.

13 Steps to RV Bathtub Replacement Project Success

Before you begin your RV bathtub replacement, first replace all RV bathtub components. But don’t try to salvage the RV bathtub enclosure since they are difficult to remove without cracking. You’ll also waste time cleaning off surface dirt and gunk. A new RV bathtub enclosure may be a little expensive, but you’ll be happier when everything is sparkling new. This goes for all parts for your RV bathtub replacement project. Re-using parts just leaves you with an unattractive mix of old and new plastic.

The next step is to measure and order carefully. Take precise measurements of the tub’s length, width, and depth. Make note of which side your drain is on. Many RV owners say that ABS plastic RV bathtubs tend to match product description directions better than fiberglass ones so check user reviews for the replacement you want.

Parts For Your RV Bathtub Replacement Project

  • Bathtub Faucet
  • Dicor Lap Sealant
  • New RV Bathtub
  • New RV Tub Surround
  • Panel Retainer Clips
  • Shower / Tub Drain
  • 100% Silicone Caulk
  • Caulking Kit
  • Channel Lock Pliers
  • Putty Knife or Flat Pry-Bar
  • Rubber Mallet
  • Screwdrivers
  • Utility Knife

Now, with everything in place, you can now begin the install.

1. Remove Shower Curtain Assembly

Retract your shower curtain and remove the top slider bar. Next, remove the catch bar and bottom guide bar. Carefully remove spool assembly.

<a href=RV bathtub replacement" />Remove the shower curtain assembly carefully without breaking it.

2. Shut Off Water and Remove Plumbing Fixtures

Remove all bathtub accessories like the shower head. Open your RV bathtub plumbing access on the wall behind behind your tub, then unscrew the plumbing. Next, remove the faucet by unscrewing mounting rings from behind the fixture.

<a href=RV bathtub replacement" />Your RV bathtub should have an access panel on the other side of the wall.

3. Gut the Tub Surround

First, remove all panel trim clips from the surround enclosure. The tines of an old fork work well to remove the clips. Just wedge underneath them and pull. Rip out the surround next.

<a href=RV bathtub replacement" />Rip out the surround and be done with it.

4. Remove the Apron Retainer Strip

Extract the metal strip that attaches the tub rim to the bathtub apron by unscrewing the retainer screws.

<a href=RV bathtub replacement" />Don’t cut your fingers on the metal retainer strip.

5. Disconnect the Tub Drain

Don’t pull the tub out until you remove the drain. Access the plumbing below the tub itself, then unscrew the drain from the P-trap.

<a href=RV bathtub replacement" />Remove the drain attachment before pulling out the tub.

6. Remove the RV Bathtub

 <a href=RV bathtub replacement" />Pulling out the tub is a one-person job.

7. Drain to the New Tub

Remove the downspout from the old tub and attach a new drain to the downspout through the hole in the bottom of new tub. The YouTube video below shows further details.

8. Re-Seat the New Bathtub

Maneuver the attached tub drain into the platform hole, then attach the downspout to your RV plumbing. Confirm the drain is sitting inside the P-trap.

9. Check the Fit

Press down on bottom of tub to ensure it is seated firmly on the platform. But if your tub doesn’t seat properly, consider cutting a 1/2″ thick plywood sized to the tub platform (just be sure to cut a hole for the downspout). Further, attach the riser to the tub platform with drywall screws. Once firmly seated, attach the downspout to the tub plumbing by screwing down the retainer ring.

<a href=RV bathtub replacement" />You may need to cut plywood to seat the tub.

10. Install the New Enclosure

Put the surround enclosure in place. Apply silicone along the tub rim, and inside the retainer clip holes. Insert new clips back into existing holes then use a rubber mallet to secure the surround to the wall.

11. Replace Plumbing Fixtures

Insert the new RV tub faucet from front side of tub. Attach retainer rings to the fixture from behind the wall. Next, attach the plumbing onto the fixture pipes. Pay attention to where hot and cold plumbing lines should go.

12. Install Shower Curtain Assembly

Attach the shower curtain reel and rods in the opposite way you removed them. Additionally, use silicone to affix the spool side to the surround. Now you can install the bottom guide bar, catch rail and top bar. Just insert the curtain first so it glides easily and connects to catch.

13. Seal and Clean

Slowly turn the water on and look for any leaks, especially from behind the tub drain. Also, dry the tub and apply 100% silicone bath sealant to all seams. So, once the caulk is dry your new RV bathtub enclosure is ready for use.

Watch the RV Bathtub Replacement Video for More Details

[embedded content]

Komentar

Posting Komentar

Postingan populer dari blog ini

How to Install Tile Flush with Hardwood Floors

Gambar
Today I’m sharing how to install tile flush with hardwood floors, like I did in my bathroom.  Can you believe the Jack and Jill bathroom finally has floors?  I’m making slow but steady progress.  The vanity area of the bathroom has a combination of hardwood and tile.  The room that contains the shower and toilet is all tile but it butts up to the wood in the other room.   Install Tile Flush with Hardwood Floors" /> I wanted the tile to be flush with the hardwood floors so I installed the tile on LATICRETE STRATA_MAT™ XT   .    It helps create an even transition between typical ¼” to 3/8″ thick tile and 3/4″thick hardwood flooring.  The STRATA_MAT XT replaces 1/4″ thick cement board — it’s much lighter, easier to cut and installs with just mortar (no screws required). install tile flush with hardwood floor" /> Installing STRATA_MAT XT I cut a piece of STRATA_MAT XT to fit in the powder room.  Then I test fit that piece and cut out the vent and toilet drain hole .  I
Baca selengkapnya

10 Amazing Shower Stall Ideas for Your Bathroom

Gambar
If you want one feature in your bathroom to be out of the ordinary then go for building or installing a shower stall that makes a difference. There are a lot of styles you can choose for a shower enclosure . For example corner shower stalls are great for a bathroom that is tight on space. Then there are different materials that can be used for example a wood, a stone or a glass shower stall . Moreover, by adding niches, benches and other accessories, you can make your shower enclosure even more cozy. So, take a look at some shower stall ideas below and choose the one you like the best: This shower stall is the perfect example of uber-modern style. It features three sided glass panels along with an integrated seat. The outer side of the seat has shelves and a cubby so that you can easily store your towels and toiletries and hence they will be in easy reach. This shower stall has classy black French doors . It is ideal for those who want an elements of design too in their shower stal
Baca selengkapnya

A Custom Six-Pac - Truck Camper Magazine

Gambar
Ken “Bear” Iddins of Buffalo Hats reveals his unique eight-foot custom Six- Pac shell model with an extremely custom, tricked-out, and modified interior.  Are those really stained glass windows ? Many of us have dreamed of designing and building our own truck camper.  One moment you’re sitting in your dinette looking at the kitchen thinking, “Why didn’t they put another cabinet right there?” and the next you’re drawing a truck camper floor plan on a napkin.  We have certainly inked a few ideas this way over the years.  Then the reality the of cost and time involved in such an endeavor hit us.  If truck campers could be built in Photoshop, we would make the world’s greatest truck camper .  Until then, we’re probably just dreaming. Then again, what if we could buy a shell and then have it custom up-fitted to our exact specifications?  That eliminates the need to design and build the exterior structure and allows us to focus on the interior we’ve always wanted.
Baca selengkapnya